Weaponeer.net
Welcome Guest
Not a member yet? Register Now! or Login
1 member and 30 guests currently online.
Search Forums:
Site Partners

This site is Gunny Approved

 


Site Login
Username

Password

Auto Login
Add me to the active users list


Forgot password | Register

Online Users
Total Users Online: 31

We have 1 member(s), 6 spiders, 30 guest(s), and 0 anonymous users online.

Members Online:
Robertautox


[ View Full List ]
[Based on the last 10 minutes]

The most online was 215 and occured on March 28 2013 at 11:38am.
We had 5 members, 203 guests, 0 anonymouse users, and 7 bots online at the same time.
Todays Visitors (131):
Robertautox, Bhrsianroode, shellycr18, yeseniaiz60, myralj3, Sergiojonia, SusanDat, catherineiu69, eddievk2, Alinkaclu, AlbertAlove, nathanielad16, BrianSet, Kathyder, amieze1, Deutschland Apotheke, stort-web-apotek, rolandnf60, amyqs4, jetloco, Richard/SIA, Gr Farmakeia, geraldinesa18, madelineow16, ronaldii18, Alinkabvv, RB20Fast, jaimezp60, CurtisVV, byronpw4, AngelaSax, mmspurg, charlesbd4, VbsfynPainna, Mjolnir1317, myrarj11, flyman, Samuel065, backbencher, junkcollector, milagrosif16, m1a76251, zzorga, Nick_Bailey, freddiett18, magdalenacz2, shortfal, bikergunnut, rickyeg4, kayetg11, RobertAgomB, corapr1, UnrebbcBladia, Josephtox, ammojoe, williehz4, Ghoulardi, feleciahn4, susannapj2, FarimfQuomy, bbrown, susiefd3, louisgz11, JeffreyAroff, marquitazd69, Zuzzy, tammikc11, lynnepq11, Msnbttomins, jamesde60, michelleux18, LastChanceArms, frankbj4, elizabethfe18, Arereehl, elisabethgp11, elaineyo4, Alisa93saupt, lorenaqk16, jayxw2, dcorb, annnx2, latashaff16, goldieeh16, rodneygt3, jesusgi3, Paraquat, Darrellneree, bertiewt69, tashalr16, verayk69, sorry0svet, Frankmes, lorabx4, LanceS4803, sheliaxb69, gracedd69, Margiealtes, jonas16, maricelact1, TaannosOrall, geraldineqw60, martinrk1, linapc2, faydq2, josefayg16, Tanner Frisby, stanleytn60, alexanderlw60, josephineiq18, coreyba4, hollyok3, thelmaxn60, terrieqq11, louisbg16, Kevinguh, joannhv4, Benfrema, SarahPaw, Artemmsk2opive, shelbyja4, brookedl69, melisawx69, jennavn2, Lekarna Online, Karmaliushix, Arereep6, Katanahic, beletevim, akawowofe, aureliabr60

DRY all recycled metals for casting
Weaponeer Forums : Casting

Posted in Casting
Members Viewing Topic: None

Post New TopicPost Reply
Prev Topic :: Next Topic
Author Message
  Chris42

E-2
E-2

Joined: December 15 2006
Location: United States
Posts: 19
Posted: December 22 2011 at 12:27pm | IP Logged Quote Chris42

Just a note about using various metals for casting - BE SURE they are DRY before adding them to a hot furnace/crucible.

Aluminum melts somewhere above 1300 degrees. Technically pure aluminum (no alloy mixed in) melts at 1218 degrees F. Brass and bronze are up above 2000 degrees, copper is above that.

Adding anything to a melt that is not completely dry can cause a steam explosion. The moisture (typically water) turns instantly to steam and expands approximately 1600 -1700 times. I have seen it happen, thought in my case it was fortunate that no one was injured. It is kind of like a molten metal hand grenade.

Here is a normal, safe procedure for seeing that the metal (aluminum, zinc, brass, copper and bronze) is dry for casting.

1) IF the furnace is cold, a crucible can be loosely filled with metal that is assumed to be dry or mostly dry. Firing the furnace from cold will heat the metal, crucible and furnace slowly and burn off any moisture. Be careful here that there aren't ANY parts (EVER ! ! ) that have trapped inside spaces. They might explode due to moisture or even due to expanding air.

2) If the furnace is hot and there is already some hot or molten metal in the crucible - the new metal to be added MUST BE PREHEATED - typically on the closed lid of the furnace. Don't over load the lid. A few pieces are enough. 5-10 minutes is usually enough time for a preheat. Then, with some tongs carefully pick up the hot pieces and lower them in to the crucible. Sometimes this can be done with the lid closed, sometimes you must open the lid, put the pieces in and then close the lid.

3) Zinc can be cast and melts relatively low (800 degrees). It is TOXIC so DO NOT breath any of the fumes. While not often found in firearms, it could be good for practice and testing molds. Virtually all the fancy old complex chrome work on cars was cast zinc and then it was chromed. Some interior plumbing fixtures are zinc. Zinc is also the metal that is mixed with copper to make brass. This should tell you to never breath the fumes from brass either.

4) Finally, recycled metals are often dirty. Some of this will burn off, the rest will become "sl*g" or "dross" on the top of the melt. This needs skimmed off before pouring. A skimmer does this, just before pouring. It looks like a big 3' spoon that has holes in it. Preheat the skimmer before using it. Do the skimming out of the furnace so the sl*g does not get spilled in the furnace. It can go into a metal sl*g bucket, to eventually get recycled at the scrapyard.

Agree Disagree Funny Informative Polite/Nice/Friendly Useful Optimistic Artistic Late Bad Spelling Bad Reading Dumb


__________________
People sleep peaceably in their beds at night only because rough men stand ready to do violence on their behalf.
George Orwell
  Status: Offline
View Chris42's Profile Search for other posts by Chris42
 
<< Prev Topic Casting Next Topic >>

If you wish to post a reply to this topic you must first login
If you are not already registered you must first register

  Post ReplyPost New Topic
Printable version Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum
Forum Jump


This page was generated in 3.6563 seconds.