Weaponeer Forums: started the project Browning 50 cal M2

Total Users Online: 33

We have 1 member(s), 7 spiders, 32 guest(s), and 0 anonymous users online.

Members Online:
Woodey

[ View Full List ]
[Based on the last 10 minutes]
The most online was 215 and occured on March 28 2013 at 11:38am.
We had 5 members, 203 guests, 0 anonymouse users, and 7 bots online at the same time.

Todays Visitors (53):

Woodey, northumbrian, 30cal, pg66, m2builder, mrjester, junkcollector, gunnuts, milwiron, scout50, Sora-tobu chiru, magmills57, Tanner Frisby, John_Steven, fabricater, nacht, backbencher, SurplusSavior, fenrirswrath, Zuzzy, Mongo, yaybacon, Tee-Bruce, Race, USMCE4retired, Wolfkin, Muscles Glasses, g85349, Sagittarii, NRADon, 1916holton, phsarge, ajruger, vipmaneg, Slowhand, taztheblade, bbrown, Africanpatriot, ikzitnu, kubel353, Mech warrior, invalidexception, voltspry, clydeh., PKw VI Tiger1, vegaguy, Tinman, Moffet64, sgnelson, djdecember, Gatling, E-4 marine, rapidroy

started the project Browning 50 cal M2
Weaponeer Forums : Blueprints and Drawings
Posted in Blueprints and Drawings Members Viewing Topic: None

Prev Topic :: Next Topic

Author

Message

nfm-depot

E-2

Joined: March 13 2012
Location: Germany
Posts: 11

Posted: May 07 2012 at 8:55am | IP Logged

We (nfm-depot) have started the project Browning 50 cal M2
It should be as faithful as possible Deteil
Although we are trade-offs as pacemakers here in Germany there are Sogut as
no cutter in inches
The scenario is when the radii are machined smooth mass eg. 4,6,8,12 mm, etc.
Here are some impressions
This image shows a preliminary assembly of manufactured components to control

Status: Offline

weaponeer

Admin Group

Joined: July 16 2005
Location: United States
Posts: 25019

Posted: May 07 2012 at 10:44pm | IP Logged

looking great

__________________
Get your Weaponeer Wear and and Pro Second Amendment T-Shirts and Mugs here http://bit.ly/sfesDw

Status: Offline

mmike956

SFC

Joined: December 29 2011
Location: United States
Posts: 191

Posted: May 14 2012 at 5:26am | IP Logged

WOW!

Status: Offline

mmike956

SFC

Joined: December 29 2011
Location: United States
Posts: 191

Posted: May 15 2012 at 5:38am | IP Logged

That looks terrific! However it looks like the extractor switch hole is on the right side plate instead of the left! It can be easily plug welded.

Status: Offline

nfm-depot

E-2

Joined: March 13 2012
Location: Germany
Posts: 11

Posted: May 16 2012 at 8:43am | IP Logged

Thank's mmike 956

The mill which must be passed at the plate!
The plate was upside down

Status: Offline

mmike956

SFC

Joined: December 29 2011
Location: United States
Posts: 191

Posted: July 13 2012 at 2:34pm | IP Logged

Sure does look good. Let's see some more pictures!

Status: Offline

<< Prev Topic

Blueprints and Drawings

Next Topic >>

If you wish to post a reply to this topic you must first login
If you are not already registered you must first register

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Forum Jump

This page was generated in 3.7813 seconds.